Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

process design of dryersproject standards and specifications… in italy

  • PROCESS DESIGN OF DRYERS (PROJECT STANDARDS

    Project Engineering Standard PROCESS DESIGN OF DRYERS (PROJECT STANDARDS AND SPECIFICATIONS) Page 4 of 48 Rev: 01 April 2011 Drying-Rate - The amount of water (kg) removed per square meter of drying area per hour. Or the volume flow rate of condensed gas at Standard Reference Atmosphere Condition of an absolute pressure of 101.325 kPa (1.01 bar ...

    Get Price
  • OFFSHORE PROCESS DESIGN (PROJECT STANDARDS

    2016-3-6 · Project Engineering Standard OFFSHORE PROCESS DESIGN (PROJECT STANDARDS AND SPECIFICATIONS) Page 5 of 28 Rev: 01 April 2011 Table 1 - Design pressure criteria for pressurised systems High trip pressure 1),2) barg Minimum margin between high trip pressure 1),2) and PSV set pressure bar 0 to 35 3,5 over 35 10 % of PSV set pressure Note:

    Get Price
  • PROCESS DESIGN OF WATER SYSTEMS (PROJECT

    2016-3-6 · Project Engineering Standard PROCESS DESIGN OF WATER SYSTEMS (PROJECT STANDARDS AND SPECIFICATIONS) Page 3 of 65 Rev: 01 April 2011 phenolphthalein endpoint at a pH 8.3). Several ions contribute to alkalinity, but it is generally due to bicarbonate (HCO)-1, carbonate (CO3)-2 and hydroxyl (OH)-1 ions.

    Get Price
  • PROCESS DESIGN OF FURNACES (PROJECT STANDARDS

    KLM Technology Group Project Engineering Standard PROCESS DESIGN OF FURNACES (PROJECT STANDARDS AND SPECIFICATIONS) Page 6 of 33 Rev: 01 April 2011 CCR Central Control Room. DN Diameter Nominal, in (mm). Eq Equation. FDF Forced Draft Fan. FE Flow Element. FSLL Flow Switch Low Low. HC Hydrocarbon. HHV Higher Heating Value. IDF Induced Draft Fan. L/D Tube …

    Get Price
  • PROJECT STANDARDS AND SPECIFICATIONS piping

    2016-3-6 · process design of piping systems (process piping and pipeline sizing) (project standards and specifications) table of content scope 3 references 3 definitions and terminology 4 symbols and abbreviations 5 units 8 process pipe sizing for plants located onshore-single phase general sizing criteria 9 fluid flow 9 reynolds number 10

    Get Price
  • PROCESS DESIGN OF COOLING TOWERS (PROJECT

    2016-3-6 · Project Engineering Standard PROCESS DESIGN OF COOLING TOWERS (PROJECT STANDARDS AND SPECIFICATIONS) Page 8 of 34 Rev: 01 April 2011 Recirculation (Recycle) - Recirculation is that portion of the outlet air which re-enters the tower. Shell - Shell is that part of a natural draught tower which induces air flow.

    Get Price
  • PROCESS DESIGN OF COMPRESSORS (PROJECT

    Project Engineering Standard PROCESS DESIGN OF COMPRESSORS (PROJECT STANDARDS AND SPECIFICATIONS) Page 2 of 47 Rev: 01 April 2011 SCOPE This Project Standards and Specifications covers the minimum requirements, basic reference data and necessary formulas for process calculations and proper selection of compressors to be used in the OGP industries.

    Get Price
  • PROCESS DESIGN OF VACUUM EQUIPMENT #03-12 Block

    2016-3-6 · Standard www.klmtechgroup.com Page : 1 of 36 Rev: 01 April 2011 KLM Technology Group #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia PROCESS DESIGN OF VACUUM EQUIPMENT (VACUUM PUMPS AND STEAM JET - EJECTORS) (PROJECT STANDARDS AND SPECIFICATIONS) TABLE OF CONTENT SCOPE 2 REFERENCES 2 …

    Get Price
  • KLM Technology Group BASIC PROCESS DESIGN

    2016-3-6 · Project Engineering Standard BASIC PROCESS DESIGN REQUIREMENTS AND CRITERIA FOR REFINERIES (PROJECT STANDARDS AND SPECIFICATIONS) Page 5 of 22 Rev: 01 June 2013 D. Design pressure at the discharge of a centrifugal pump 1. As a general rule the design pressure will be the maximum of the values calculated by the two following formulas :

    Get Price
  • THE ROLE OF A SPECIFICATION IN THE DESIGN PROCESS:

    THE ROLE OF A SPECIFICATION IN THE DESIGN PROCESS: A CASE STUDY M. N. Sudin, S. Ahmed-Kristensen and M. M. Andreasen Keywords: specification, design process, design tasks 1. Introduction Design specification is a description of the desired solution to …

    Get Price